Pool Cue, Cuetec Avid Surge Break cue, Black/gold

36650

Available on backorder

SKU: 21,269,57,0 Categories: , , , Tags: , , ,

Description

Pool Cue, Cuetec Avid Surge Break cue, Black/gold

 

 

LIGHT YEARS AHEAD OF THE COMPETITION.

The Pool Cue, Cuetec Avid Surge Break is good for the money. Just as their name implies, AVID Surge Series break cues efficiently deliver an unrivaled rush of energy. Constructed utilizing multiple-layers of oriented glass fibers bonded to a kiln-dried, A+ grade a low-deflection Power+ front-end, Acueweight Gen II adjustment system, and is DUO extension compatible. With so much technology inside, your break is sure to surge ahead of the competition.

Specifications;

  • Surge Power Pro Taper
  • Silver and Gold Power Twist Rings
  • Steel Collar and Butt Cap
  • Laser etched Cuetec and AVID butt cap logos
  • Duo Smart Extension Ready Bumper
  • Acueweight generation II adjustment system
  • CT logo joint protectors
  • Shaft: AVID Surge Low-Deflection Glass Fiber Bonded Break Shaft
  • Shaft Length: 29”
  • Tip: Power+ Phenolic with Glass Pad (Extra Hard)
  • Joint: 3/8×14 Cuetec Joint (21.30mm)
  • Shaft Collar: 1.5mm Black Phenolic
  • Weight: 19oz (Acueweight adjustable in 0.25 oz. increments)

 

AVID CARE & MAINTENANCE;

Maintaining the Cuetec AVID shaft’s finish.

AVID shafts must never be sanded or modified. Using any abrasive on the surface of the shaft will damage the shaft’s finish and possibly weaken the shaft’s glass composite bonding layers and discharge potentially materials that could be hazardous to your health. Any polishing, sanding or treatment of the surface of the shaft with abrasives or chemicals of any kind will void the shaft’s warranty.

Never use baby powder, hand chalk, talcum powder or other shaft treatments on a Cuetec AVID shaft.

To clean the surface of your AVID shaft, you will need just a few materials; Isopropyl Alcohol (75% or higher) and two (2) clean and debris-free soft cloth towels.

Step 1.

Remove any dust and debris by wiping the shaft with a soft clean cloth.

Step 2.

Apply a reasonable amount of Isopropyl Alcohol (75% or higher) to a clean, soft cloth towel. Next, work the towel up and down the length of the shaft, while rotating your hand around its circumference. It is possible that dirt will be visible on the towel.
This is completely normal. Continue working the shaft with the same motion until all areas have been thoroughly wiped, then allow a moment for the surface to dry.

Changing the tip on your Cuetec AVID Shaft.

AVID shafts feature a light-weight white sighting ferrule. This inclusion to AVID shaft’s front-end construction allows for easier tip replacement over the life of the shaft. When changing the tip, it is important to clean and resurface the ferrule. The minimum height of the ferrule must be greater than 2mm to maintain the shaft’s warranty coverage.

* Always use a recognized and proven cue-smith. Never allow a cue-smith to sand or modify the shaft’s finish when installing a new tip.

 

Replacing the ferrule on your Cuetec AVID Shaft.

While unlikely, should the ferrule on your AVID shaft ever need to be replaced, it must be done by an authorized Cuetec repair center. This is required due to the complex nature of the bonding agents used and to ensure that no damage is done to the shaft’s glass composite bonding layers. To locate an authorized repair center near you, contact customerservice@cuetec.com.

 

Adjusting an AVID Cue’s weight

Cuetec AVID cues utilize a cartridge based weight system. To adjust the weight of your cue. Remove the bumper using a 10mm hex wrench key. After the bumper has been removed, insert a Phillips head screwdriver into the butt, turning it to the left to remove any installed weights. Acueweights are available in .25 .oz, .05 .oz, and 1.0 .oz, increments.

 

Warpage

Cuetec AVID shafts feature a limited-lifetime warranty against warpage.

 

Abuse

AVID shafts are not engineered to tolerate considerable lateral pressure. They should never be flexed excessively, hit on other objects or treated with any abrasives, whether they are solid or liquid.

 

Shaft Diameter

AVID shaft diameters should never be modified. Any sanding, polishing or abrasive treatment could jeopardize the ultra-thin glass bonding surface layer and immediately void the AVID shaft’s warranty.

IMPORTANT INFORMATION:

Please note: Due to differences in monitors and monitor settings, it is possible that colours in product photos appear different to the actual product.

 

Additional information

Weight 0,8 kg
Dimensions 85 × 7 × 7 cm

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.